NCS-Core Exam Dumps - Nutanix NCS Professional Questions and Answers

In this scenario, the connectivity issue arises because the VLAN settings require a specific configuration on the vSwitch settings when using LACP. When using LACP for load balancing network traffic, the vSwitch or Distributed Switch must be configured with the "Route based on IP hash" load balancing algorithm. This setting is necessary to properly distribute the traffic across the LACP bonded links. Not selecting this setting in vSwitch0 settings would result in improper handling of network packets over the LACP bonded links, thereby causing the hosts and CVMs to be unreachable. Adjusting the vSwitch settings to "Route based on IP hash" should resolve the connectivity issue.References: VMware vSphere Networking documentation, Nutanix Bible LACP configuration guidelines.

Before going on-site to deploy a Nutanix cluster, the following prerequisites are crucial:

• A. Complete the kickoff call and validate the BOM (Bill of Materials): This ensures that all necessary components are accounted for and any discrepancies or missing items are addressed prior to installation.
• C. Validate whether the cluster questionnaire is complete and if the physical switch configurations are complete: Ensuring that all relevant customer and network information is obtained and validated is critical to avoid delays or issues during the physical installation and configuration of the cluster.

References:

• Nutanix Bible (https://www.nutanixbible.com), particularly sections on pre-deployment planning and validation.
• Nutanix University: NCS-Core 6.8 Training (https://university.nutanix.com), covering the importance of thorough preparation and documentation before on-site engagements.

Ref: https://portal.nutanix.com/page/documents/kbs/details?targetId=kA00e000000CuaDCAS

In the scenario described, the configuration shown in the exhibit indicates that there is an "active-backup" bond mode. If a shut command is executed on the switchport that connects the node to the 5k1 switch (assuming it's the active link), the passive link should take over. This response ensures no loss of connectivity as the passive link becomes active in the absence of the primary (active) link.References: Nutanix Bible, Nutanix University NCS-Core 6.8 learning materials

The customer is experiencing VM performance issues characterized by excessive read/write I/Os on CVMs and excessive motion of VMs due to the Distributed Resource Scheduler (DRS) in an ESXi-based Nutanix cluster. This is likely caused by the DRS migration threshold being set to Aggressive, which leads to frequent rebalancing of workloads across the cluster, causing high I/O and VM motion. Adjusting this setting to a less aggressive level can help reduce unnecessary VM motions and stabilize performance.References: Nutanix Bible, Nutanix University NCS-Core 6.8 learning materials

In a typical Nutanix deployment using a flat switch, the Foundation VM, the CVM, and the Hypervisor should all be on the same subnet to facilitate seamless communication and management operations during the initial setup and operation. The IPMI, being a management interface, can be on a different subnet as it serves a different purpose primarily for remote management at the hardware level and does not need to be on the same subnet as the other components for cluster functionality.References:

• Nutanix University - NCS-Core 6.8 Learning Path
• The Nutanix Bible, Network Configuration chapter (https://www.nutanixbible.com/)

In the scenario where a consultant observes ping timeouts after shutting down one of the links during a port failover test, the issue is likely due to a Native VLAN mismatch on the switchport. The configuration settings shown in the second exhibit indicate different native VLANs for the switch ports connected to the Nutanix node. This mismatch can cause connectivity issues when one of the links is down, as VLAN tagging inconsistencies prevent proper fallback and routing of traffic.References: Cisco Networking Troubleshooting Guide, Nutanix Network Configuration Best Practices.

When using the Foundation VM in a desktop virtualization environment and nodes are not being discovered, the first setting that the consultant should verify is the network adapter configuration, specifically ensuring it is set to a Bridged Adapter. This setting allows the virtual machine hosting the Foundation VM to connect directly to the physical network, making other network nodes visible and reachable during the discovery process. This direct network connection is critical for the Foundation tool to function correctly and discover other nodes.References: Nutanix Bible, Nutanix University

When a consultant is unable to install virtualization software on a laptop, the most suitable versions of Foundation to resolve this issue would be Foundation Portable (Option B) and Foundation Applet (Option D). Both these versions are designed to be used in environments where installing additional virtualization software might not be feasible. Foundation Portable can be run from a USB drive, and the Foundation Applet is a Java-based tool that can run directly on a host machine without the need for a full virtual machine environment.References: Nutanix Foundation Installation Guide, Nutanix Support Portal.

As the consultant concludes the project, to assist the customer with repeating the deployment process at a dark site, the best items to deliver would be:

• A trial license activation code for Prism Starter, which will allow the customer to begin using the Nutanix cluster immediately without initial extra costs.
• Creating an account for access to the Nutanix Support Portal, ensuring the customer can access support and documentation as needed for troubleshooting and learning.
• A guide for dark site deployments using Nutanix standards, which will provide step-by-step instructions tailored to the specific challenges of deploying in a location with no direct internet connectivity.These resources are critical for enabling the customer to independently deploy and manage Nutanix clusters under the unique constraints of a dark site.References: Nutanix Deployment Guide, Nutanix Support Portal Documentation.