LEED-AP-BD+C Exam Dumps - USGBC Leadership in Energy and Environmental Design (LEED) Questions and Answers

The make and model of fixtures is required in determining the baseline for the Water Efficiency Prerequisite, Indoor Water Use Reduction. This information is used to calculate the baseline water consumption of the building, which is then compared to the proposed water use to determine the percentage reduction.References: LEED AP Building Design + Construction (LEED AP BD+C) V4 resources 1

QUSTION NO: 147

In order to comply with Indoor Environmental Quality Credit, Enhanced Indoor Air Quality Strategies, Option 2. Additional Enhanced IAQ Strategies

A. all entrances to the building must have entryway systems 10 ft. (3 m) long in the direction of travel

B. CO2 monitors must be fitted in all densely occupied spaces and configured to provide an alert

C. all outdoor air supply systems must have an airflow measurement device that measures at least 90% of the airflow

D. all particle filters in the ventilation system must meet Comité Européen de Normalisation (CEN) standard Class F7 or better

Answer: D

To comply with the Indoor Environmental Quality Credit, Enhanced Indoor Air Quality Strategies, Option 2, all particle filters in the ventilation system must meet the Comité Européen de Normalisation (CEN) standard Class F7 or better. This requirement ensures that the air quality inside the building is maintained at a high standard, contributing to the health and well-being of the occupants.References: LEED AP Building Design + Construction (LEED AP BD+C) V4 resources 1

An economic advantage of the infill site is that it reduces the need for new utility infrastructure. This is because the infill site is located within an existing urban area that already has access to water, sewer, electricity, and other utilities1. The developer can save on the costs of extending or installing new utility lines and services to the rural greenfield site, which may not have adequate or reliable utility infrastructure2. The other options are not economic advantages, but rather environmental benefits of the infill site. Protecting greenfields and farmland, preserving habitat and natural resources, and reducing potential damage to an existing stream are all positive outcomes of avoiding development on the rural greenfield site, but they do not directly translate into monetary savings for the developer3.

References:

•High-priority site, p. 1

•The Economics of Infill Development, p. 2

•LEED v4 for Building Design and Construction, p. 69

The Sustainable Sites (SS) Credit: Rainwater Management (A) would be affected by the slope analysis results. Slopes, especially those near water bodies, can significantly impact stormwater runoff volume and patterns. Managing runoff in sloped areas is crucial to minimize erosion, reduce pollutants, and protect nearby water bodies. This credit aims to reduce runoff volume and improve water quality by implementing effective rainwater management strategies based on site conditions. Other credits, like Environmental Site Assessment (B) or Sensitive Land Protection (C), don’t focus on runoff management.

This option requires the project team to focus on reducing the water consumption of the school project, because it is located in a basin that depends on the seasonal snowmelt for its water supply1. Installing efficient plumbing fixtures, such as low-flow faucets, toilets, and showerheads, can help save water and reduce the demand on the local water resources2. This option can also help the project achieve the LEED credits for outdoor and indoor water use reduction3.

References: = LEED v4: Building Design + Construction Guide, Water-Efficient Plumbing Fixtures, Water Efficiency | U.S. Green Building Council.

The Whole Building Simulation option is used to meet the Energy and Atmosphere Prerequisite, Minimum Energy Performance for a hospital project. This option involves creating a detailed computer model of the building to simulate its energy performance and identify opportunities for improvement.References: LEED AP Building Design + Construction (LEED AP BD+C) V4 resources 1

The best design approach for the office building is D. Recover waste energy through exhaust air energy recovery systems. This is because:

Installing glazing with a higher solar heat gain factor would increase the cooling load and energy consumption of the building, especially in an extremely humid climate where heat gain is high1.

Installing photovoltaic panels on the sides of the building would generate electricity from solar radiation, but it would not reduce the cooling load or energy consumption of the building, unless the electricity is used to power a heat pump or other cooling device2.

Increasing outdoor air intake quantities during summer months would provide more fresh air to dilute the indoor pollutants and improve the indoor air quality, but it would not reduce the cooling load or energy consumption of the building, unless it is combined with a ventilation system that recovers waste energy from the exhaust air stream34.

An exhaust air energy recovery system (ERV) is a type of mechanical ventilation that uses a heat exchanger to transfer heat between two streams of air: one that enters the building and one that exits. The ERV pre-cools and dehumidifies the incoming ventilation air by sending the rejected heat into the exhaust airstream to cool the condenser coil at a lower temperature. This reduces both the cooling load and energy consumption of the building, as well as improving its indoor humidity levels34. An ERV can also provide some fresh outdoor air to meet ASHRAE Standard 62 ventilation rates5.

Therefore, an ERV is a more efficient and effective design approach than glazing, photovoltaic panels, or increased outdoor air intake quantities for reducing the annual energy cost for operating an office building in an extremely humid climate and shaded by very large adjacent buildings on all four sides.

References: 1: LEED v4: Building Design + Construction Guide - U.S. Green Building Council 2: LEED AP BD+C Exam | U.S. Green Building Council 3: Energy Recovery Systems - Nortek Air Solutions 4: Energy Recovery Ventilators - Greenheck 5: Mechanical Ventilation Types: Exhaust, Supply, Balanced & Energy Recovery

Materials and Resources Credit, Building Product Disclosure and Optimization - Sourcing of Raw Materials, Option 2. Leadership Extraction Practices

Natural rubber flooring is a bio-based material that can contribute to the achievement of Option 2 of the Sourcing of Raw Materials credit, which requires using products that meet at least one of the responsible extraction criteria for at least 25%, by cost, of the total value of permanently installed building products in the project1. By meeting the Sustainable Agriculture Standard (SAN), the natural rubber flooring demonstrates that it has been produced in a way that conserves biodiversity, protects natural resources, and enhances social and economic well-being2. Therefore, the cost of the substituted flooring ($80,000) can be counted towards the credit threshold.

References:

Reference Guide for Building Design and Construction v4 – Pages 263-2641

Sustainable Agriculture Standard | Rainforest Alliance3

Coordinating open space features early during the site planning phase is a viable strategy for optimizing open space under Sustainable Sites Credit, Open Space. This can help to preserve natural habitats, reduce heat island effects, and enhance human health and well-being. The credit requires that the project provide outdoor space that is at least 30% of the total site area, and that at least 25% of that outdoor space meets certain criteria for vegetated, pervious, or shaded areas. References:

LEED credit library: This is the USGBC’s comprehensive listing of all the LEED credits available in pursuing certification for your project. The credit library contains the requirements and guidance for each credit, as well as the web-based reference guide for the Building Design and Construction rating system.

Open Space: This is the specific credit page for the Open Space credit under the Sustainable Sites category. It provides the intent, requirements, and strategies for achieving the credit, as well as the number of points available and the applicable project types.

Step by Step Approach to Comply with the Open Space Credit in LEED v4: This is a blog post that explains the steps and calculations involved in complying with the Open Space credit. It also provides some examples and tips for optimizing open space design.

In the Integrative Process, the Owner’s Project Requirements (OPR) should be created during the predesign phase and edited throughout the project (C). The OPR documents the owner’s goals and objectives, guiding design decisions to align with these priorities. Updating the OPR as necessary ensures that project design and construction remain aligned with the owner’s vision and LEED requirements.

The bonus location valuation factor in several Materials and Resources credits under LEED AP BD+C V4 is intended to incentivize the purchase of products that support the local economy. Products extracted, manufactured, and produced within 100 miles (161 km) of the project are valued at 200% of their cost within the calculations1. This adds value to locally produced products and materials2.

References:

LEED Quiz 8: Ch. 9 Materials & Resources Flashcards | Quizlet

LEED 2009 vs. LEED v4: Regional Materials - LaForce, LLC