LEED-Green-Associate Exam Dumps - USGBC Leadership in Energy and Environmental Design (LEED) Questions and Answers

Renewable Energy Certificates (RECs) are tradable, non-tangible energy commodities that represent the environmental attributes of one megawatt-hour of electricity generated from renewable sources, such as wind, solar, hydro, or biomass1. RECs can be purchased by anyone, regardless of their location or utility provider, to support the development of renewable energy and reduce their carbon footprint2. RECs can also help projects earn points for the LEED v4 Innovation credit for Green Power and Carbon Offsets, which requires the purchase of at least 50% of the total building energy use from renewable sources or offsets for a minimum of five years3.

References:

Using Renewable Energy for LEED Certification

Renewable Energy Certificates For Green Building Explained

LEED v4, Renewable Energy, and Carbon Offsets

A 100% vegetated roof coverage best addresses both heat island effect and rainwater runoff from the roof only. A vegetated roof, also known as a green roof, is a layer of living plants that covers the roof surface. A vegetated roof reduces the heat island effect by providing shade, evapotranspiration, and insulation, lowering the roof temperature and the surrounding air temperature. A vegetated roof also reduces rainwater runoff by retaining and absorbing precipitation, decreasing the volume and peak flow of stormwater leaving the roof. The other options are not as effective as a 100% vegetated roof coverage in addressing both heat island effect and rainwater runoff from the roof only. A 100% high-albedo roof reflects more solar radiation than a conventional roof, reducing the heat island effect, but it does not reduce rainwater runoff. A 20% high-albedo and 80% conventional roof has a lower reflectance than a 100% high-albedo roof, resulting in a higher heat island effect, and it does not reduce rainwater runoff either. A 50% standing seam copper and 50% vegetated roof has a lower vegetated area than a 100% vegetated roof, resulting in less shade, evapotranspiration, insulation, retention, and absorption, leading to a higher heat island effect and more rainwater runoff. References: LEED Green Associate Candidate Handbook, page 27; USGBC, [Sustainable Sites], page 3.

Blackwater is wastewater that contains fecal matter and pathogens, such as from toilets. Greywater is wastewater that is less contaminated, such as from showers, sinks, and washing machines1. However, the classification of kitchen sink wastewater may vary depending on local codes and regulations. Some states and authorities consider kitchen sink wastewater as blackwater because it may contain food waste and germs123. Others consider it as greywater if it meets certain quality standards and is used for beneficial purposes, such as irrigation or toilet flushing45. A CIR (Credit Interpretation Request) is a process to seek clarification on a specific credit or prerequisite in a LEED rating system, but it does not change the definition of blackwater or greywater.

References:

Greywater Reuse | WaterSense | US EPA4

Greywater - California Department of Water Resources5

What Is Greywater? What Is Blackwater? | HomeServe USA1

Grey Water / Reclaimed Water | University of Maryland Extension2

What is meant by the terms Gray water and black water3

Credit Interpretation Requests (CIRs) | U.S. Green Building Council

The project boundary is the area within which the project team has authority to implement the LEED requirements. It is important to clearly identify the project boundary to define the limits of site disturbance, which can affect the environmental performance of the project. For example, limiting site disturbance can help reduce soil erosion, protect natural habitats, and conserve water resources. The project boundary also determines the scope of the site assessment and the applicability of some credits. References: LEED v4 BD+C Reference Guide, Introduction, page 13

ASHRAE 90.1-2010, Appendix G is the referenced standard for defining the baseline building performance for energy simulation modeling in LEED v4 for Building Design and Construction. The baseline building is a hypothetical building that represents the minimum energy performance required by ASHRAE 90.1-2010, which is a standard for energy efficiency in buildings. The baseline building is used as a benchmark to compare the proposed design of the project and to calculate the percentage of energy cost savings achieved by the project. The baseline building performance is evaluated by following the procedures and assumptions specified in Appendix G of ASHRAE 90.1-2010, such as building envelope, lighting, HVAC systems, service water heating, and renewable energy.

The other options are not relevant to the question, as they are standards for different aspects of green building, such as thermal comfort (ASHRAE 55-2010), air filtration (ASHRAE 52.2-2007), and ventilation (ASHRAE 62.1-2010).

References: LEED v4 Reference Guide for Building Design and Construction, p. 341 1; [ASHRAE website]

The Energy Policy Act (EPACT) of 1992 set standards for indoor water fixtures like toilets and faucets, which are used as a baseline for determining water savings in LEED projects. The 2005 amendment to the EPACT further updated these standards. References: LEED Green Associate Candidate Handbook, U.S. Green Building Council resources

This formula is used to calculate the percentage of restoration area for the LEED v4 credit SSc2: Protect or Restore Habitat1. The restoration area is the portion of the site that is restored with native or adapted vegetation, and the total previously disturbed site area is the area that was altered by human activity before the project2.

References := NC-v4.1 SSc2: Protect or Restore Habitat | LEEDuser, LEED CERTIFICATION- REQUIREMENTS FOR SS CREDIT: PROTECT OR RESTORE …

A scorecard rule for LEED Credit Point Allocation is that there is a maximum of 100 base points available for each rating system. These points are distributed among the different credit categories based on their relative contribution to the overall environmental impact and human health benefits of a project. The point allocation process is informed by a weighting methodology that uses life cycle assessment and expert judgment to assign weights to each of the LEED impact categories. The impact categories reflect the goals and priorities of LEED, such as reversing climate change, enhancing human health, protecting water resources, and promoting social equity. References: LEED v4 Impact Category and Point Allocation Process Overview1; LEED scorecard5

Sizing the building appropriately means designing the building to meet the needs and expectations of the occupants, without creating excess space that would require more energy to heat, cool, and light. This strategy reduces the energy demand of the building and also saves on construction costs and materials.

References:

LEED v4 for Building Design and Construction, p. 36

LEED Green Associate Candidate Handbook, p. 11

Water closets, also known as toilets, are fixtures that use water to flush human waste into a sewer or septic system. The unit of measure for water closets is gallons (liters) per flush, which indicates the amount of water used for each flushing cycle. The water efficiency of water closets can vary depending on the design, technology, and regulation of the fixture. The LEED rating system encourages the use of water-efficient fixtures that reduce water consumption and wastewater generation12. References: LEED v4 Green Associate Candidate Handbook1, EPA’s WaterSense Toilets2