ECP-206 Exam Dumps - Ericsson Certified Associate Questions and Answers

 IPv6 link-local addresses are designed to be used in three situations: for neighbor discovery, for local IP communication on the IPv6 capable routers, and for addressing on a single link for purposes such as auto-address configuration. Neighbor discovery is a protocol that allows IPv6 nodes to discover each other and learn their link-layer addresses on a local network. Neighbor discovery uses link-local addresses to send and receive messages such as router advertisements, router solicitations, neighbor advertisements, and neighbor solicitations34. Local IP communication on the IPv6 capable routers refers to the ability of routers to exchange routing information or management traffic using their link-local addresses as source and destination addresses. This reduces the need for global unicast addresses on router interfaces that are not reachable from outside the local network35. Addressing on a single link for purposes such as auto-address configuration refers to the use of link-local addresses to enable IPv6 nodes to obtain an address without manual configuration or a DHCP server. Link-local addresses can be automatically derived from the interface identifier in the modified EUI-64 format or randomly generated. Link-local addresses can also be used to test the connectivity of a link before obtaining a global unicast address36.

References: Understand the IPv6 Link-Local Address - Cisco, Link Local Address - GeeksforGeeks, IPv6 Address Types | Link-Local, Global Unicast, etc.⋆ IPCisco, MPLS Label Distribution Protocol Commands - Cisco

The device that will fragment IPv6 packets is the source host. Fragmentation is a process of dividing a large packet into smaller pieces that can fit the maximum transmission unit (MTU) of the network link. In IPv4, fragmentation can be performed by either the source host or any intermediate router along the path. However, in IPv6, fragmentation is only allowed at the source host, and routers are not allowed to fragment packets. This reduces the processing overhead and complexity at routers and avoids potential fragmentation attacks. If a router receives an IPv6 packet that is too large for the next-hop link, it will drop the packet and send an ICMPv6 Packet Too Big message back to the source host56.

References: IPv6 address - Wikipedia, IPv6 Fragmentation - Cisco

LDP relies on IGP for all routing-related decisions. LDP is a protocol that distributes labels in an MPLS environment, but it does not perform any routing functions. LDP uses the underlying routing information provided by an IGP, such as OSPF or IS-IS, to forward label packets. LDP and IGP do not exchange their databases at regular intervals, but rather use hello messages to maintain adjacencies and sessions. References: Ericsson IP Networking - Routing Protocols, Label Distribution Protocol - Wikipedia

Two statements that are true about the Ericsson Router 6000 series are:

• The Router 6000 uses the same building practice and accessories as the Ericsson Radio System. The Ericsson Radio System is a modular and scalableradio access network solution that supports multiple standards, bands, and layers. The Router 6000 series is fully integrated into the Ericsson Radio System, using the same building practice and accessories such as mounting kits, cables, power supplies, etc. This simplifies installation, operation, and maintenance of both radio and transport equipment78.
• The Router 6000 products range from all-outdoor small site routers to large aggregation routers. The Router 6000 series consists of three main products: the Router 6672 for access, the Router 6675 for pre-aggregation, and the Router 6274 for metro aggregation. The Router 6672 is an all-outdoor small cell site router with high-capacity and low-power consumption. The Router 6675 is a combined access and E-RAN switch with hardware-accelerated IPSec and high-accuracy internal clock. The Router 6274 is a high-capacity metro aggregation router with SDN functionality and flexible interface options78.

References: Router 6000 Series - Ericsson, New Ericsson Router 6000 series couples radio and IP transport for 5G future - Global Brands Magazine

The route type that is restricted in an OSPF stub area is type 5. Type 5 LSAs are external LSAs that are generated by ASBRs to advertise routes from other routing domains or protocols into OSPF. Type 5 LSAs are flooded throughout the OSPF domain by default, except in stub areas. Stub areas are special OSPF areas that block type 5 LSAs from entering the area in order to reduce the size of the LSDB and the routing table. Stub areas only receive information about intra-area routes (type 1 and 2 LSAs), inter-area routes (type 3 LSAs), and a default route (type 3 LSA with destination 0.0.0.0/0) from the ABRs910.

References: Introduction to OSPF Stub Areas - NetworkLessons.com, What Are OSPF Areas and Virtual Links? - Cisco

Referring to the exhibit, the correct statement is that the service provider’s P routers are not aware of the customers’ routes. This is because P routers only need to forward MPLS packets based on their labels, without looking into their IP headers or VPN information. The P routers do not have any VRFs configured for the customers, nor do they participate in MP-BGP sessions with other PE routers. The PE routers are responsible for maintaining VRFs for each customer and for exchanging VPN routes with other PE routers using MP-BGP910.

References: Layer 3 VPNs (L3VPN) - Cisco, MPLS VPN - Wikipedia

A P router is a provider router that is part of the service provider’s core network in an MPLS environment. A P router does not have any customer routes or VPN information, but only has information about how to reach other P routers and PE routers in the same MPLS domain. A P router performs label switching, which means that it forwards labeled packets based on their top label in the label stack. A P router can perform two possible label actions:

• Swap: The P router replaces the incoming label with a new label that corresponds to the next hop along the label-switched path (LSP). The new label is determined by looking up the label forwarding information base (LFIB) based on the incoming label and interface.
• PHP: The P router removes the top label from the packet at the penultimate hop before reaching the egress PE router. This is done to avoid an extra lookup on the egress PE router, which can forward the packet based on its IP header or another label in the stack.

A P router does not perform push or drop actions on labels. A push action means adding one or more labels to the packet, which is done by an ingress PE router when initiating an LSP. A drop action means discarding a packet, which is done by any router when there is no matching entry in its LFIB or routing table. References: Provider (P) Router in IP MPLS Network - Cisco Community, MPLS Fundamentals: Forwarding Labeled Packets - Cisco Press, MPLS Label Switching | MPLS Operation | Push, Swap,Push ⋆ IPCisco

The statement about IPv6 that is correct is that broadcast has been replaced with multicast. IPv6 is the most recent version of Internet Protocol (IP), which provides an identification and location system for computers on networks and routes traffic across the Internet. IPv6 has several improvements over IPv4, such as a larger address space, simplified header format, enhanced security, and better support for mobility and QoS.One of the changes in IPv6 is that it does not support broadcast, which is a method of sending a packet to all nodes on a network segment. Instead, IPv6 uses multicast, which is a method of sending a packet to a group of nodes that have joined a multicast address34.

References: IPv6 - Wikipedia, What Is IPv6? - Cisco