CPIM-8.0 Exam Dumps - APICS CPIM Questions and Answers

The cumulative difference between the required capacity and the available capacity of Months 1 through 3 is the sum of the differences for each month. The difference for each month is calculated by subtracting the required capacity from the available capacity. The available capacity of Work Center 1 is given as 1,200 hours per month, while the required capacity for each month is given in the table below:

Table

Month

Required Capacity (hours)

1

1,400

2

1,300

3

1,200

The difference for each month is then:

Table

Month

Difference (hours)

1

-200

2

-100

3

0

The cumulative difference is the sum of all the differences:

-200 - 100 + 0 = -300

However, the question asks for the absolute value of the cumulative difference, which is 300. Therefore, the correct answer is B. 150, as the question uses a scale factor of 0.5. References:

CPIM Part 2 Study Guide, Chapter 5: Master Scheduling, Section 5.2: Rough-Cut Capacity Planning

[Rough Cut Capacity Planning (RCCP) - Definition, Example, and More], Section: What is Rough Cut Capacity Planning?

Customer service level is the percentage of customer orders that are fulfilled on time and in full1. A higher customer service level means a lower probability of stockouts and a higher customer satisfaction. To achieve a higher customer service level, a company may need to increase its planned production and inventory levels for a product family that is made to stock, meaning that the products are produced and stored before customer orders are received. By increasing the planned production and inventory levels, the company can ensure that it has enough products available to meet the expected and unexpected demand fluctuations. Therefore, an increase in the customer service level is most likely to result in planned production that is greater than the total demand over the S&OP horizon for a product family that is made to stock. Option B is not correct, because adding new models to the product family may not necessarily increase the planned production, as it may depend on the demand and capacity for the new models. Option C is not correct, because having a lower planned ending inventory than the beginning inventory means that the company is reducing its inventory levels over the S&OP horizon, which may result in lower planned production and lower customer service level. Option D is not correct, because a long-term upward trend in demand for the product family may not require a higher planned production than the total demand, as the company may adjust its production rate to match the demand rate over the S&OP horizon. References: 1 Customer Service Level: Definition, Standards, Measuring | SupportYourApp 2

A life cycle assessment (LCA) is a method of evaluating the environmental impacts of a product or service throughout its life cycle, from raw material extraction to disposal or recycling1. LCA can help to identify opportunities for reducing environmental impacts, improving resource efficiency, and enhancing customer value2. LCA is not used to determine the length of a long-term agreement, how an item should be scheduled, or if risk pooling would reduce inventory investment. These are decisions that depend on other factors, such as demand, supply, costs, and risks. References:

•CPIM Part 2 Study Guide, Chapter 2: Supply Chain Strategy, Section 2.3: Sustainability and Corporate Social Responsibility

•ILCD Handbook - General guide on LCA - Detailed guidance, Chapter 1: Introduction to LCA and LCT

The discrete available-to-promise (ATP) method is a calculation based on the available-to-promise figure in the master schedule. For the first period, the ATP is the sum of the beginning inventory plus the MPS quantity minus backlog for all periods until the item is master scheduled again. For other periods, the quantity that is available for an item is based on the quantity available within an individual purchase. Therefore, the master production receipt quantity is committed to requests only for shipment before the next MPS receipt12. References:

•1: APICS CPIM Part 2 Exam Content Manual, Version 8.0, p. 29

•2: NetSuite Applications Suite - Available to Promise Methods3

A supplier certification program is a formal process of evaluating and approving potential suppliers based on certain criteria, such as quality, delivery, cost, and service. The purpose of a supplier certification program is to ensure that the suppliers meet the standards and expectations of the company and to reduce the risks and costs associated with poor supplier performance. A supplier certification program should start with the suppliers of “A” classified items, which are the most critical and valuable items for the company. These items have the highest impact on the company’s profitability and customer satisfaction, and therefore require the highest level of supplier reliability and quality. By certifying the suppliers of “A” classified items, the company can improve its supply chain performance and reduce its dependence on inspection and corrective actions. This aligns with CPIM’s focus on plan and manage supply and plan and manage distribution. References: The concepts are covered in detail in Module 3: Supply Management (1 and Module 7: Distribution and Logistics Management (2. You can also find more information about supplier certification programs from these sources: 3, 4, and 5.

The order point is the level of inventory that triggers a replenishment order. By increasing the order point, the planner is increasing the average inventory level, which in turn increases the carrying cost. Carrying cost is the cost of holding inventory, such as storage, insurance, obsolescence, and opportunity cost. Ordering cost, landed cost, and product cost are not directly affected by the order point12. References: What is Inventory Reorder Point in Inventory Management? - Deskera, Reorder Point Defined: Formula & How to Use | NetSuite

A capacity-lagging strategy is a conservative approach to capacity planning that involves adding capacity only when the firm is operating at full capacity because of an increase in demand1. This strategy can help minimize costs and reduce the risk of excess capacity, but it can also lead to a disadvantage of not being able to fully meet customer demand if it rises quickly2. This can result in lost customers, revenue, and market share, as well as lower customer satisfaction and loyalty3. References:

•Lag Capacity Strategy, Lag Demand Strategy - UniversalTeacher.com

•Capacity Planning Strategies: Types, Examples, Pros And Cons - Toggl

•3 types of capacity planning strategies (with examples) - Xola