CFPS Exam Dumps - NFPA Fire Protection Specialist Questions and Answers

According to NFPA 230: Standard for the Fire Protection of Storage, 2015 Edition, building codes should limit the size of an unsprinklered facility used for the processing and storage of Municipal Solid Waste (MSW) built of type V construction to 7,500 ft2 (697 m2). This is based on the assumption that the MSW has a heat release rate of 18,000 Btu/ft2-min (200 kW/m2) and a fire growth rate of 0.046 min-1.Type V construction is defined as a type of construction in which the structural elements, exterior walls, and interior walls are of any materials permitted by the code123

References:

• NFPA 230: Standard for the Fire Protection of Storage
• 5 Types of Construction per the IBC | Building Code Trainer
• 2.4 MUNICIPAL SOLID WASTE LANDFILLS - U.S. Environmental Protection Agency

The answer is C. Human factor plays a significant role in most industrial fire and explosion losses.According to a study by Allianz Global Corporate & Specialty (AGCS), human error is the cause of 80% of all industrial accidents, including fires and explosions1. Human error can include mistakes, negligence, violations, or sabotage. Some examples of human errors that can lead to fires and explosions are:

• Improper handling or storage of flammable or combustible materials
• Failure to follow safety procedures or regulations
• Lack of training or supervision
• Poor maintenance or inspection of equipment or machinery
• Ignoring or disabling alarms or warning systems
• Smoking or using open flames near hazardous areas
• Intentional or accidental ignition of explosives or incendiaries

To prevent or reduce the impact of human errors, industrial facilities should implement effective risk management strategies, such as:

• Providing regular and adequate training and education for workers and managers
• Establishing and enforcing clear and consistent safety policies and rules
• Conducting thorough and frequent audits and inspections
• Installing and maintaining reliable fire protection systems and equipment
• Developing and practicing emergency response and evacuation plans
• Encouraging a positive safety culture and communication among all stakeholders

valve at the inspector’s test connection.

For wet-pipe automatic sprinkler systems, the only proper way to test the operation of a vane-type water flow alarm initiating device is to open the valve at the inspector’s test connection. This is a small valve that is located at the end of a pipe that is connected to the sprinkler system, usually at the most remote or highest point. The inspector’s test connection simulates the flow of a single sprinkler head and activates the vane-type water flow switch, which in turn triggers the fire alarm panel and the external alarm devices.Opening the valve at the inspector’s test connection also allows the water to drain from the system, preventing corrosion and freezing1234

Opening the main (2 in. diameter) drain is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not create enough flow to activate the switch. The main drain is used to drain the entire sprinkler system for maintenance or repair purposes, and it is usually located at the main riser or the fire department connection.Opening the main drain may also cause a pressure drop in the system, which could affect the performance of the sprinklers1234

Opening the alarm test by-pass valve at the system’s main riser is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not simulate the actual flow of a sprinkler head. The alarm test by-pass valve is used to test the operation of the external alarm devices, such as the water motor gong or the electric bell, without activating the fire alarm panel. The alarm test by-pass valve is usually located near the alarm check valve or the water flow switch, and it allows water to flow through a small orifice to the alarm devices.Opening the alarm test by-pass valve does not create enough flow to activate the vane-type water flow switch1234

Opening the check valve from the city connection is not a proper way to test the operation of a vane-type water flow alarm initiating device, because it does not create any flow in the sprinkler system. The check valve from the city connection is used to prevent the backflow of water from the sprinkler system to the city water supply, and it is usually located at the fire department connection or the main riser.Opening the check valve from the city connection does not affect the water flow in the sprinkler system, and it does not activate the vane-type water flow switch1234

References:

• Fire Sprinkler Flow Switch & Tamper Switch Inspection & Maintenance3
• Sprinkler System Water Flow Device Testing - ORR Protection2
• VSR-AT Auto-Test Waterflow Alarm Switch | Potter Electric4
• WFDNA Series Vane-type Waterflow Detectors - Steel Fire Equipment5

When using water mist as an extinguishing mechanism, the effectiveness of a fine mist depends on the momentum and direction of the spray relative to the fire. The momentum and direction of the spray determine how well the mist can penetrate the fire plume and reach the flame zone, where the mist droplets can evaporate and cool the fire, displace oxygen, and dilute the fuel vapors. The mist spray should have sufficient momentum to overcome the buoyancy and entrainment of the fire plume, and the direction of the spray should be aligned with the fire plume to avoid deflection and dispersion. The ability of the mist to directly spray on the fire, how much mist diverts to the compartment boundaries, and how much conductive heat the mist system will absorb are not the main factors affecting the extinguishing effectiveness of a fine mist.

References:Water Mist Systems Overview | NFPA;Engineering Relations for Water Mist Fire Suppression Systems;Effectiveness of Swirl Water Mist Nozzles for Fire Suppression

The background color used from the source to the outlets of a nitrous oxide medical gas system is blue. This is the standard color coding for nitrous oxide cylinders and pipelines in medical gas pipeline systems12. The color coding helps to identify the gas type and prevent accidental misconnections or cross-contamination3. The color coding also indicates the pressure and flow characteristics of the gas system4. References:

• Colour coding of copper pipes in Medical gas pipeline system according …
• Doc 177 20 Medical Gas Cylinders Colour Coding - EIGA
• Medical Gas Coding Color Chart & Explanation - Bay Corporation
• Medical gases Health Technical Memorandum 02-01: Medical gas pipeline …

Hazardous waste

Explore

The correct answer is C. Environmental Protection Agency (EPA) standards require solid waste be treated as hazardous if it is a listed waste and/or meets the characteristics prescribed by the standard for toxicity, reactivity, corrosivity, andignitability.A listed waste is a waste that appears on one of the four lists of hazardous wastes in the Code ofFederal Regulations (CFR) part 261 subpart D1.A characteristic waste is a waste that exhibits one or more of the following traits: toxicity, reactivity, corrosivity, or ignitability2. Toxicity is the ability of a waste to leach harmful chemicals into the environment. Reactivity is the tendency of a waste to undergo violent chemical reactions or generate toxic gases. Corrosivity is the property of a waste to corrode metals or damage living tissues.Ignitability is the capacity of a waste to catch fire under certain conditions2.These characteristics are defined by specific tests and criteria in the CFR part 261 subpart C3.The EPA standards for hazardous waste are based on the Resource Conservation and Recovery Act (RCRA), which is the federal law that regulates the management of solid and hazardous waste in the United States4.

Fire pump

Explore

A multistage centrifugal fire pump is defined as having two or more impellers on one shaft as a single unit. A multistage centrifugal pump is a type of centrifugal pump that uses multiple impellers to increase the pressure and flow of water.Each impeller acts like a single-stage pump within a chain of pumps, and the water passes through each impeller in series, gaining pressure and velocity at each stage1.A multistage centrifugal fire pump is used to provide high-pressure water for fire protection systems, especially in high-rise buildings or large industrial facilities2.A multistage centrifugal fire pump can be driven by an electric motor, a diesel engine, or a steam turbine3.References:

• Our Guide to Multistage Centrifugal Pumps | C&B Equipment
• Fire Pump Types | NFPA
• NFPA 20: Changes to the fire pump standard - Consulting

In the plastics industry, the four broad areas of processing arepolymerization,conversion,finishing, andrecycling1.Polymerization is the process of creating plastic resins from monomers or pre-polymers, using chemical reactions such as addition, condensation, or ring-opening2.Conversion is the process of transforming plastic resins into plastic products, using various methods such as injection molding, blow molding, extrusion, rotational molding, and thermoforming3.Finishing is the process of adding value to plastic products, such as coating, printing, welding, or assembling4.Recycling is the process of recovering plastic waste and converting it into new plastic products or raw materials, using mechanical, chemical, or biological methods5. Therefore,manufacturingis not one of the four broad areas of processing in the plastics industry, as it is a general term that encompasses all the stages of producing plastic products from raw materials.References:

• Plastics Manufacturing: Types of Plastic and Processes - Deskera
• Plastics industry - Wikipedia
• Methods of Processing Plastic - Plastics Industry
• Plastic recycling - Wikipedia
• Polymerization - an overview | ScienceDirect Topics

The correct answer is D. The greatest number of civilian home fire deaths can be attributed to the common room, living room, or family room area of origin in the home. According to a report by the NFPA, based on data from the National Fire Incident Reporting System (NFIRS) and NFPA’s fire experience survey, 31 percent of the civilian home fire deaths in 2017-2021 occurred in fires that started in the common room, living room, or family room. This was followed by 29 percent of the deaths in fires that started in the bedroom or sleeping area, and 12 percent of the deaths in fires that started in the kitchen or cooking area. The common room, living room, or family room area of origin is also the leading area of origin for home fires and civilian home fire injuries, accounting for 24 percent and 21 percent of those incidents, respectively. Some of the common causes of fires in the common room, living room, or family room include smoking materials, heating equipment, electrical equipment, candles, and fireplaces. To prevent fires and fire deaths in the common room, living room, or family room, the NFPA recommends the following safety tips:

• Keep smoking materials away from anything that can burn. Use deep, sturdy ashtrays and wet cigarette butts before discarding them.
• Keep space heaters at least 3 feet away from anything that can burn. Turn them off when you leave the room or go to sleep.
• Have a qualified electrician inspect and repair any faulty wiring or outlets. Avoid overloading circuits or extension cords. Unplug appliances when not in use.
• Keep candles in sturdy holders and away from children, pets, and anything that can burn. Blow them out when you leave the room or go to sleep.
• Have your chimney and fireplace cleaned and inspected annually by a professional. Use a metal or glass screen to keep sparks from flying out. Dispose ofashes in a metal container with a lid, and keep it outside at least 10 feet away from your home.
• Install smoke alarms on every level of your home, inside each bedroom, and outside each sleeping area. Test them monthly and replace the batteries at least once a year. Consider installing a home fire sprinkler system for added protection.