NS0-521 Exam Dumps - Netapp NCIE SAN ONTAP Questions and Answers

To restrict access to a newly created LUN to specific hosts, the administrator should configure theigroup(initiator group). An igroup is used to control which initiators (hosts) are allowed to access specific LUNs. This ensures that only authorized hosts can access the storage, enhancing security and access control.

For more details, refer to:

NetApp Documentation on iGroups​ (NetApp)​.

The recommended setting for using the NetApp ONTAP LUN fractional reserve is to set the space guarantee to "volume". This setting ensures that the required space for overwrites in the volume is reserved, preventing potential write failures when snapshot copies are created. This setup helps in maintaining the performance and reliability of the storage system by ensuring there is always enough space allocated for the LUN.

For further details, you can refer to:

NetApp Community Discussion on Fractional Reserve

NetApp Documentation on Space Management

To restore a LUN from a SnapMirror Synchronous destination, the following steps must be taken:

Release the relationship: This step is necessary to break the SnapMirror relationship, allowing the LUN to be restored independently.

Delete the relationship: After releasing the relationship, deleting it ensures that there are no residual dependencies or configurations that might interfere with the restore process.

For more information, refer to:

NetApp Documentation on SnapMirror Synchronous​ (NetApp)​​ (NetApp)​.

For a successful deployment of a switchless HA pair with two NetApp DS224C shelves in an already populated rack, it is crucial to verify:

Rack units: Ensure that there are enough rack units available to accommodate the new shelves and any associated equipment. Proper planning of space in the rack is essential for a neat and functional setup.

Power connections: Verify that there are sufficient and appropriately rated power connections available. Ensuring proper power distribution and redundancy is critical for the reliability and uptime of the storage system.

For more details, refer to:

NetApp Documentation on Rack Installation

NetApp Community Discussion on Power Connections

To validate that the entire network path supports jumbo frames after an iSCSI implementation, you should perform a ping test from the host with fragmentation. This involves using the ping command with specific options to test jumbo frame support:

ping -M do -s 8972

In this command:

-M do ensures the packets are not fragmented.

-s 8972 sets the packet size to 8972 bytes (9000 bytes MTU minus 28 bytes for the ICMP header).

By confirming that the large packets are successfully transmitted without fragmentation, you can validate that the network path, including switches and adapters, supports jumbo frames.

For more details, you can check:

NetApp Documentation - iSCSI Configuration and Best Practices​ (NetApp)​​ (NetApp)​.

To configure an SVM to use NVMe/FC, the following steps are necessary:

Add the FC protocol: This step involves enabling the Fibre Channel protocol on the SVM, which is required to support NVMe over Fibre Channel.

Create an NVMe/FC LIF: Logical Interfaces (LIFs) must be created to handle NVMe traffic over the Fibre Channel network. These LIFs enable the NVMe namespace access to the host systems.

These steps ensure that the SVM is correctly set up to use NVMe/FC, allowing for efficient and high-performance access to NVMe storage.

For more information, refer to:

NetApp NVMe/FC Configuration

When planning to upgrade the UCS Server BIOS and Cisco NX-OS system running on the switches in a NetApp AFF ASA cluster environment, theInteroperability Matrix Tool (IMT)is the recommended resource to check compatibility with the new versions. The IMT provides detailed compatibility information for various hardware and software components, ensuring that the planned upgrades will not cause any interoperability issues.

For further details, refer to:

NetApp Interoperability Matrix Tool

Active IQ OneCollect is a NetApp tool designed to collect configuration and performance data from your storage environment, including SAN solutions. It can automate the creation of difference reports by capturing the current state of the system and comparing it against a baseline, thereby showing any changes or deviations from the intended design.

For further details, refer to:

NetApp Active IQ OneCollect Documentation

When the number of paths exceeds the recommended configuration for SAN deployment, it can cause performance issues. To address this problem, you can:

Use Selective LUN Mapping (SLM): SLM allows you to control which LIFs (Logical Interfaces) are used to access specific LUNs, thus reducing the number of paths and potentially improving performance by aligning with best practice configurations.

Reconfigure the fabric switch zoning: Adjusting the zoning on the fabric switches can help manage and optimize the number of paths, ensuring that there are not too many paths that could lead to inefficient I/O operations and performance degradation.

For more details, refer to:

NetApp SAN Host Configuration

NetApp Best Practices for SAN

To ensure the best performance in an iSCSI SAN implementation:

Connect host and storage ports to the same switches: This minimizes latency and maximizes the efficiency of data paths by ensuring direct connections within the same network segment.

Configure Jumbo frames in the entire data path: Setting a larger Maximum Transmission Unit (MTU) size reduces the overhead for processing each packet, thus improving overall network performance. Ensuring Jumbo frames are configured end-to-end in the data path is crucial for optimal performance.

For further details, check:

NetApp Best Practices for iSCSI

NetApp Community Discussion on iSCSI Performance