H12-351_V1.0 Exam Dumps - Huawei Certification Questions and Answers

• A. In EAP termination mode, an access device encapsulates EAP packets sent by an 802. IX client Into RADIUS packets, without processing the data in the EAP packets. This statement is false because in EAP termination mode, an access device extracts information from EAP packets, encapsulates the information into RADIUS packets, and sends the RADIUS packets to an authentication server2.
• D. The EAP termination mode simplifies the processing on an access device and supports various authentication methods. However, this mode requires an authentication server to support EAP and have high processing capability. This statement is false because it describes the EAP relay mode, not the EAP termination mode2.

Therefore, A and D are the correct answers. References: 2: https://support.huawei.com/enterprise/en/doc/EDOC1100086527

• MP: Mesh node that uses IEEE 802.11 MAC and PHY protocols for wireless communication. This node supports automatic topology discovery, automatic route discovery, and data packet forwarding. It can provide both mesh service and user access service1.
• MPP: MP node that connects a WMN to MPs on other types of networks. This node can function as a portal for communication between internal mesh nodes and external networks1.
• Neighbor MP: Neighboring MP with which an MP prepares to establish a mesh link1.
• Candidate MP: AP that directly communicates with a mesh node2.

https://support.huawei.com/enterprise/en/doc/EDOC1100064365/90f2391e/configuration-examples-for-mesh  2: https://support.huawei.com/enterprise/en/doc/EDOC1100169459/8d79210e/configuring-wireless-mesh-networking

B is false because generally, a STA roams when it detects that the signal strength is less than -70 dBm or -65 dBm, not -75 dBm.

References: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/wlan-roaming-and-signal-strength

According to the Huawei documents and resources, EAP termination and EAP relay are typical 802.1X authentication modes between the access device and authentication server. In EAP termination mode, the access device terminates EAP packets and encapsulates them into RADIUS packets. In EAP relay mode, the access device directly encapsulates the received EAP packets into RADIUS using EAP over RADIUS (EAPoR) packets2. Therefore, A and B are the correct answers. References: 2: https://support.huawei.com/enterprise/en/doc/EDOC1100086527

iMaster NCE-CampusInsight analyzes network issues during correlation analysis of poor-QoE clients, including coverage, interference, throughput, and hardware issues. It also provides suggestions for network optimization based on the analysis results.

References: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/correlation-analysis-of-poor-qoe-clients

Navi WAC networking is a networking mode that uses a WLAN Access Controller (WAC) to manage and control APs. It can provide different authentication and security policies for different user groups, such as employees and guests. Guest data is isolated from the internal network to prevent security threats.

References: https://support.huawei.com/enterprise/en/doc/EDOC1100064352/9aadccc0/navi-wac-networking

In a dual-link backup scenario, when the active link recovers, the AP waits for 15 Echo intervals before switching back to the original primary WAC. This prevents frequent link switchovers caused by unstable links.

References: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/dual-link-backup

According to the Huawei documents and resources, the chronological order during the 802.11r fast roaming process between WACs is as follows:

2.The STA accesses the network through API. This is the initial association process before roaming.

1.The STA initiates an 802.11 FT authentication request to AP2. This is the first step of the roaming process when the STA moves to a new AP.

3.AP2 starts the reassociation timer, and sends an 802.11 FT authentication response to the STA. This is the second step of the roaming process when AP2 responds to the STA’s request and sets a timer for reassociation.

4.The STA generates and installs a P TK based on the information contained in the response frame. This is the third step of the roaming process when the STA derives a new pairwise key for encryption.

5.The STA sends a reassociation request to AP2. This is the fourth step of the roaming process when the STA requests to reassociate with AP2.

6.AP2 generates and installs a PTK according to PMK-RI and information contained in the request frame. This is the fifth step of the roaming process when AP2 derives the same pairwise key as the STA.

7.After receiving the reassociation request, AP2 disables the reassociation timer, and then sends a reassociation reg onse to the STA. This is the sixth step of the roaming process when AP2 confirms the reassociation with the STA and stops the timer.

8.The STA receives the response frame of AP2. The roaming process is complete. This is the final step of the roaming process when the STA completes the handover to AP2.

Therefore, 2, 1, 3, 4, 5, 6, 7, 8 is the correct answer. References: https://support.huawei.com/enterprise/en/doc/EDOC1100169459/8d79210e/configuring-wireless-mesh-networking

Satellite positioning can achieve high positioning accuracy in outdoor scenarios, but not in indoor scenarios. This is because satellite signals are easily blocked or interfered by buildings, walls, ceilings, and other obstacles in indoor environments.

References: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/satellite-positioning

C is false because the license file only affects the number of devices that can be managed by iMaster NCE-CampusInsight, not the data display.

E is false because the UTC time of devices does not need to be consistent with that of iMaster NCE-CampusInsight.

References: https://support.huawei.com/enterprise/en/doc/EDOC1100058940/8a8f1c9b/data-display