CWAP-404 Exam Dumps - CWNP Certification Questions and Answers

The data rate at which the PHY preamble was transmitted is 6 Mbps. The PHY preamble is a part of the PPDU that is transmitted before the PHY header and the PSDU. The PHY preamble consists of a series of training fields that help the receiver to detect and synchronize with the signal. The PHY preamble is always transmitted at a fixed data rate that depends on the type of PPDU (e.g., OFDM, HT, VHT, HE). For an 802.1 lac data frame on channel 52, which uses VHT PPDUs, the data rate for the PHY preamble is 6 Mbps. This data rate does not depend on MCS (Modulation and Coding Scheme), which only affects the data rate for the PSDU. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 4: 802.11 Physical Layer, page 99-100

Observing the problem is the most important step in the WLAN troubleshooting methodology among those listed. This step involves capturing and analyzing the relevant data from the wireless network, such as packets, frames, spectrum, and performance metrics. Observing the problem helps to verify the existence and scope of the issue, identify the root cause and possible solutions, and validate the results of any actions taken. The other steps are also important, but they are not as critical as observing the problem12 References:

• CWAP-404 Study Guide, Chapter 1: Troubleshooting Methodology, page 15
• CWAP-404 Objectives, Section 1.2: Observe the problem

Real-time packet decodes are not a consideration when configuring a long-term, forensic packet capture and saving all packets to disk. Real-time packet decodes are useful for live analysis and troubleshooting, but they consume CPU and memory resources that could affect the performance of the capture process. For a long-term, forensic packet capture, it is more important to consider the analyzer location, the total capture storage space, and the individual trace file size. These factors affect the quality and quantity of the captured packets and the ease of post-capture analysis34 References:

• CWAP-404 Study Guide, Chapter 2: Protocol Analysis, page 49
• CWAP-404 Objectives, Section 2.1: Configure protocol analyzers

An AIFS is a variable interframe space introduced by 802.11e to help prioritize medium access for different Access Categories (ACs). An interframe space is a period of time that a STA (station) has to wait before attempting to access the medium. An AIFS is a type of interframe space that varies depending on the AC of the traffic. An AC is a logical queue that corresponds to a QoS (Quality of Service) level for different types of traffic. There are four ACs defined by 802.11e: AC_VO (Voice), AC_VI (Video), AC_BE (Best Effort), and AC_BK (Background). Each AC has a different AIFSN (Arbitration Interframe Space Number) value, which determines how long it has to wait before attempting to access the medium. A lower AIFSN value means a higher priority and a shorter waiting time. The other options are not correct, as they do not describe what an AIFS is. An AIFS is not a medium access method introduced by 802.11n, but never implemented, as it is part of the 802.11e standard and widely used in QoS-enabled WLANs. An AIFS is not a form of aggregation performed at the PHY layer based on 802.11e UP values interpreted from DSCP values, as aggregation is a technique that combines multiple frames into one larger frame to improve efficiency and throughput, not prioritization or medium access. An AIFS is not the shortest period of time a STA can sleep, as sleeping is a power saving mode that allows a STA to conserve battery power by periodically turning off its radio, not accessing the medium. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 7: QoS Analysis, page 194-195

A VoIP phone, using WMM Power Save, requests data frames buffered at the AP by transmitting a trigger frame, which is a QoS Null frame or a QoS Data frame. WMM Power Save is a power saving mode that allows a STA (station) to conserve battery power by periodically sleeping and waking up. WMM Power Save is based on WMM (Wi-Fi Multimedia), which is a QoS (Quality of Service) enhancement that provides prioritized and differentiated access to the medium fordifferent types of traffic. When a STA sleeps, it cannot receive any data frames from the AP, so it informs the AP of its power save status by setting a bit in its MAC header. The AP then buffers any data frames destined for the sleeping STA until it wakes up. When a STA wakes up, it sends a trigger frame to the AP, indicating its AC (Access Category), which is a logical queue that corresponds to its QoS level. A trigger frame can be either a QoS Null frame or a QoS Data frame, depending on whether it has any payload or not. The AP then responds with one or more data frames from the same AC as the trigger frame, followed by an ACK or BA (Block Acknowledgement) frame from the STA. The other options are not correct, as they are not used by a VoIP phone using WMM Power Save to request data frames buffered at the AP. A PS-Poll (Power Save Poll) frame is used by a STA using legacy power save mode, not WMM Power Save mode, to request data frames buffered at the AP. A PS-Poll frame does not indicate any AC or QoS information. Setting the More Data bit in the MAC header to 1 does not request any data frames from the AP, but indicates that there are more data frames to be sent by the STA or received by the STA. Transmitting a WMM Action frame does not request any data frames from the AP, but performs various management actions related to WMM features, such as admission control, parameter update, etc. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 7: QoS Analysis, page 198-199

 In the 2.4 GHz band, probe requests are usually sent at the minimum basic rate from an unassociated STA. A probe request is a type of management frame that is transmitted by a STA to discover available BSSs in its vicinity. A probe request can be sent on one or more channels in either passive or active scanning mode. In passive scanning mode, a STA listens for beacon frames from APs on each channel. In active scanning mode, a STA sends probe requests on each channel and waits for probe responses from APs. A probe request is usually sent at the minimum basic rate, which is the lowest data rate among the supported rates that is required for all STAs to join and communicate with a BSS. The minimum basic rate can vary depending on the configuration of each BSS, but it is typically one of these values: 1 Mbps, 2 Mbps, 5.5 Mbps, or 11 Mbps in the 2.4 GHz band. The other options are not correct, as they do not reflect how probe requests are usually sent in the 2.4 GHz band. MCS 0 is a modulation and coding scheme used by 802.11n/ac devices in either band, but it is not a data rate per se. 6 Mbps is a data rate used by OFDM devices in either band, but it is not usually configured as a minimum basic rate in the 2.4 GHz band. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 5: 802.11 MAC Sublayer, page 123-124

It is possible to distinguish between OFDM 20 MHz transmissions and HT 20 MHz transmissions when looking at an FFT plot. OFDM and HT are two different modulation schemes used by 802.11 WLANs. OFDM is used by legacy 802.11a/g devices, while HT is used by newer 802.11n/ac devices. OFDM and HT have different spectral characteristics that can be observed on an FFT plot. OFDM transmissions have a flat spectrum with sharp edges, while HT transmissions have a tapered spectrum with rounded edges. This is because HT uses guard intervals and cyclic prefixes to reduce inter-symbol interference and improve performance. The other options are not correct, as they do not describe different modulation schemes or channel widths that can be distinguished on an FFT plot. References: [Wireless Analysis Professional Study Guide CWAP-404], Chapter 3: Spectrum Analysis, page 70-71

The most likely cause of higher airtime utilization on the first 20 MHz of the 80 MHz channel is non-Wi-Fi interference. Non-Wi-Fi interference can prevent an AP from using its full channel width, as it will degrade the signal quality and increase the noise floor on some parts of the channel. This will force the AP to fall back to a narrower channel width, such as 20 MHz or 40 MHz, to maintain communication with its clients. The waterfall plot can help identify non-Wi-Fi interference by showing spikes or bursts of RF energy on specific frequencies or sub-channels. The other options are not correct, as they do not explain why only the first 20 MHz of the channel has higher airtime utilization. References: [Wireless Analysis Professional Study Guide], Chapter 3: Spectrum Analysis, page 74-75