2V0-41.23 Exam Dumps - VMware Certification Questions and Answers

A group is a logical construct that represents a collection of objects in NSX, such as segments, segment ports, virtual machines, IP addresses, MAC addresses, tags, or security policies. A group can be used to define dynamic membership criteria based on various attributes or filters. A group can also be used as the scope of a distributed firewall rule, which means that the rule will apply to all the traffic that matches the group membership criteria32

The correct answer is to enable the option All LB VIP Routes on the Tier-1 gateway route advertisement settings. This option allows the Tier-1 gateway to advertise the NSX Advanced Load Balancer LB VIP routes to the Tier-0 gateway and other peer routers, so that the end users can reach the production website by using the VIP address1. The other options are not relevant for this scenario.

To mark the correct answer by clicking on the image, you can click on the toggle switch next to All LB VIP Routes to turn it on. The switch should change from gray to blue, indicating that the option is enabled. See the image below for reference:

https://docs.vmware.com/jp/VMware-NSX/4.1/installation/GUID-B7E7371E-A9F6-4880-B184-E00A62C0C818.html

According to the VMware NSX Documentation, these are the prerequisites for adding nodes to an NSX Management Cluster using the NSX UI:

• All nodes must be in the same subnet and have IP connectivity with each other.
• A compute manager must be configured and associated with the NSX Manager node.
• The NSX Manager node must have a valid license.
• The NSX Manager node must have a valid certificate.

According to the VMware NSX Documentation, this is the NSX feature that can be leveraged to achieve consistent policy configuration and simplicity across sites:

• NSX Federation: This feature allows you to create and manage a global network infrastructure that spans across multiple sites using a single pane of glass. You can use this feature to synchronize policies, segments, gateways, firewalls, VPNs, load balancers, and other network services across sites.

According to the VMware NSX Documentation, Switch Visualization is a feature in the NSX UI that shows the mapping between the virtual NIC and the host’s physical adapter for virtual machines running on an ESXi transport node. You can use Switch Visualization to view details such as port ID, MAC address, VLAN ID, IP address, MTU, port state, port speed, port type, and port group for each virtual NIC and physical adapter.

https://docs.vmware.com/en/VMware-NSX/4.1/installation/GUID-55E5C735-18AD-43F8-9BE5-F75D5B8C6EDB.html

According to the VMware Knowledge Base article 1, the CLI command to set the log level of the NSX Manager to debug mode is set service manager logging-level debug. This command can be used when the NSX UI is inaccessible or when troubleshooting issues with the NSX Manager1. The other commands are incorrect because they either use a wrong syntax or a wrong service name. The NSX Manager service name is manager, not nsx-manager2. The log level parameter is logging-level, not log-level3.

https://kb.vmware.com/s/article/55868

An NSX administrator can use TCP, UDP, or TLS protocols to transfer log messages to a remote log server. These protocols are supported by NSX Manager, NSX Edge, and hypervisors for remote logging. A Log Insight log server supports all these protocols, as well as LI and LI-TLS, which are specific to Log Insight and optimize network usage. HTTPS, SSH, and SSL are not valid protocols for remote logging in NSX-T Data Center. References: : VMware NSX-T Data Center Administration Guide, page 102. : VMware Docs: Configure Remote Logging

The command vmkping ++netstack=geneve -d -s 1572  is used to check the VMware kernel ports for tunnel end point communication. This command uses the geneve netstack, which is the default netstack for NSX-T. The -d option sets the DF (Don’t Fragment) bit in the IP header, which prevents the packet from being fragmented by intermediate routers. The -s 1572 option sets the packet size to 1572 bytes, which is the maximum payload size for a geneve encapsulated packet with an MTU of 1600 bytes. The  is the IP address of the remote ESXi host or VM. References: : VMware NSX-T Data Center Installation Guide, page 19. : VMware Knowledge Base: Testing MTU with the vmkping command (1003728). : VMware NSX-T Data Center Administration Guide, page 102.